ASA VPN settings 2A. Enable VPN terminations on the outside interface. Lab1(config)# crypto isakmp enable outside 2B. Create a transform set (phase 2 settings). This should match the settings defined in step 1O above. Jan 20, 2015 - For example, I use a VPN client on my iPhone, iPad, and Mac to connect to. This allows me to manage my network remotely across the secure VPN tunnel that's been. For instance, the Cisco ASA doesn't support route-based VPNs. Using a standard router configuration that's hands-off once completed. In the policy groups are applied properties like url-list, port-forwarding list, SVC configuration (for the tunnel mode client) and so on. Apply the url-list and the port-forward list defined in the previous step (3.b Configure the context properties). Configure the SSL VPN Client (SVC) to allow the remote access for the network 192.168.1.0/24. Lab1(config)# crypto ipsec transform-set 3des-sha esp-3des esp-sha-hmac 2C. Define Phase 1, these settings can be shared across multiple VPNs. Therefore if these settings already exist, it may not be necessary to create it. This should match step 1H and 1J above. If there are existing isakmp policies that do not match your desired settings, use the next available policy #. Lab1(config)# crypto isakmp policy 10 lab1(config-isakmp-policy) # authentication pre-share lab1(config-isakmp-policy) # encryption 3des lab1(config-isakmp-policy) # hash sha lab1(config-isakmp-policy) # group 2 lab1(config-isakmp-policy) # lifetime 86400 lab1(config-isakmp-policy) #exit 2D. Define the local network(s) group. This should match the remote network defined in step 1K above. Lab1(config)# object-group network Local-encrypt lab1(config-network)# network 172.16.20.0 255.255.255.0 lab1(config-network)# ex lab1(config)# 2E. Define the remote network(s) group. This should match the local network defined in step 1C above. Lab1(config)# object-group network Remote-encrypt lab1(config-network)# network 192.168.1.0 255.255.255.0 lab1(config-network)# ex lab1(config)# 2F. Create an access list that allows traffic from your local network (step 2D) and remote network (step 2E). The access-list name (“remote_vpn” in this example) can be named anything that signifies this tunnel. It is not recommend to use port filtering (for example, allowing only HTTP traffic) as Cisco firewalls do not do a good job of VPN port filtering. Lab1(config)# access-list remote_vpn permit ip object-group Local-encrypt object-group Remote-encrypt 2G. Outlook 2016 for mac print in black and white women. Freedome vpn for mac pc. Create a crypto map that ties the Phase 2 settings to the remote peer. The “match address” statement should contain the name of the access-list created in step 2F. The Peer address should match the IP address of the Checkpoint firewall. The transform set will contain the name of the set defined in step 2B. The lifetime should match the Phase 2 lifetime in step 1J. Lab1(config)# crypto map mymap 10 match address remote_vpn lab1(config)# crypto map mymap 10 set peer 192.168.1.254 lab1(config)# crypto map mymap 10 set transform 3des-sha lab1(config)# crypto map mymap 10 set security-association lifetime seconds 3600 2H. Define the tunnel type and set the pre-shared key. The pre-shared key should match the key specified in step 1I. Lab1(config)# tunnel-group 192.168.1.254 type ipsec-l2l lab1(config)# tunnel-group 192.168.1.254 ipsec-attributes lab1(config-tunnel-ipsec)# pre-shared-key abc123 lab1(config-tunnel-ipsec)# exit 2I. Make sure that the traffic in the VPN is not natted. There are several ways to define nat translations. In the below example, an access list is created and is added to the Nat 0 statement (Nat 0 is not translated) on the inside interface (assuming the local network is behind the inside interface). Lab1(config)# access-list nonat permit ip object-group Local-encrypt object-group Remote-encrypt lab1(config)# nat (inside) 0 access-list nonat 2J.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |